WEBER INLET FITTING, AN -6 TO WEBER 12MM
-6 To Weber 12mm Inlet Fitting
All Weber IDA carbs come with a useless banjo fitting we have never figured out how to use (unless you tap it 1/8-pipe and use a “barb” fitting). This will replace the stock inlet fitting with -6AN so you can use braided hose.
The 12mm Stat-O-Seal is strongly recommended for this fitting — it is at: WEBER INLET SEAL, STAT-O-SEAL FOR 12MM
We also have a 90° fitting for 8mm / 5/16″ push on hose at: WEBER INLET FITTING for 8mm (5/16″) push on hose
| SKU: | 30606-M12D |
WEBER INLET FITTING, AN -6 TO WEBER 12MM
$14.45
Related Products:
-
CABLE THROTTLE, 79-85 12A
Throttle Cable, 79-85 12A
This WAS discontinued by Mazda BUT we are having them made for us.
The replacement is made using a combo of another MAZDA cable and modifications to it.
Click Here for a Weber 48IDA Suggested Parts List
SKU: 41-6600-FA01 Manufacturer SKU: FA01-41-660 -
HEATSHIELD, 74-95 ALL 12A & 13B
Heatshield, 74-95 All 12A & 13B
Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 16219 -
WEBER SHAFT LEVER, 48+51IDA MAZDA CABLE
Weber Shaft Lever, 48+51 IDA Mazda Cable
For “U.S. Style” manifolds – where the cable pulls from BELOW shaft.Click Here for a Weber 48IDA Suggested Parts List
Browse our Weber Carbs, Manifolds and Parts section
SKU: 444.614-04 -
BOOK WEBER HAYNES, WEBER MANUAL
Book, HAYNES, Weber Manual
Browse our Weber Carbs, Manifolds and Parts section
SKU: 10240 -
WEBER SHAFT LEVER, WITH STOP PIN LEFT
Weber Shaft Lever, With Stop Pin Left.
14ga steel
We have these “stops” made for us so the throttle STOP is on the same side of the carb as the throttle PULL. Adjusted correctly this prevents the throttle shaft from being bent when full throttle is applied.
This is our latest design that “includes” the washer that covers the shaft bearing. This also allows more thread engagement of the nut onto the throttle shaft as you no longer use the original bearing cover washer.All descriptions refer to a front mounted rotary engine in a rear wheel drive car.
There are two types of manifold for downdraft IDAs: fuel inlet on engine side with throttle cable pulling from above the throttle shaft, and fuel inlet on the fender side, with the throttle cable pulling from below the throttle shaft. The manifold determines the carb orientation. It is best to have the cable pull, the idle speed screw, throttle stop, and return spring all on the same end of the carb. If this is not done, you will twist the throttle shaft, which can lead to various poor running conditions.
Click Here for a Weber 48IDA Suggested Parts ListBrowse our Weber Carbs, Manifolds and Parts section
SKU: MAT460-L -
WEBER IDA BASE GASKET, 3MM THICK
Weber IDA Base Gasket, 3mm Thick
Browse our Weber Carbs, Manifolds and Parts section
SKU: 99005.123
You May Also Like:
-
VALVE AIR CONTROL, 83 FEDERAL/CANADA –NLA–
VALVE AIR CONTROL, 83 FEDERAL/CANADA
Sorry, this item has been discontinued by Mazda.
1983 Only Without California emissionsSKU: 13-7200-N231 Manufacturer SKU: N231-13-720 -
VALVE VACUUM DELAY, GREEN/BLACK
Vacuum Delay Valve Green/Black. Arrow on body points to black end
SKU: 20-3090-8574 Manufacturer SKU: 8574-20-309 -
VALVE VACUUM 1-WAY, 93-95 ALL METAL
1-Way Vacuum Valve, 93-95 All Metal
SKU: 13-8900-NF01 Manufacturer SKU: NF01-13-890 -
BPAV GASKET, 86-88 ALL
Bypass Air Control Valve Gasket 86-88 All
SKU: 20-661A-N326 Manufacturer SKU: N326-20-661A -
VALVE AIR CONTROL, CHECK VALVE- ALL
Check Valve for All Air Control Valves
SKU: 13-7300-1480 Manufacturer SKU: 1480-13-730 -
Reviews
There are no reviews yet.