Part #
Part #
| Mazdatrix RX-8 Home Page | Click part number for price | View Cart |
| RX8 Lower Control Arm Bushings | |||
|---|---|---|---|
| This is an aluminum bearing housing with a spherical bearing installed offset to add negative camber to the front of the RX8. Kit does both L&R control arms. | MAZDASPEED Part # |
04-8001-0000 | |
| Drop Engineering Part # |
B-RX8-03LCA | ||
| RX8 Front Upper Control Arm Bushings | |||
|---|---|---|---|
| Delrin and Stainless Bushnigs, Front Upper Control Arm. Kit does both L&R arms. | MAZDASPEED Part # |
04-8002-0000 |  Installation Information |
| Drop Engineering Part # |
B-RX8-03UCA | ||
| RX8 Heim Jointed Rear Suspension Links | ||
|---|---|---|
| A set of all ten rear stock control and toe links with heim jointed ends replacing the stock fixed bushing ends. Stock links are modified on the bushing end, and fitted with adjustable Heim Joints. Ball Joint end remains stock. | 04-8003-0000 |  |
| RX8 Rear Subframe Aluminum Bushing Kit | ||
|---|---|---|
| Bushings made out of billet aluminum to solidly mount the rear subframe. | 04-8004-0000 |  |
| RX-8 Engine Carburetor/Manifold Adapter Plate | ||
| 6-Port 04-11 | 16480 |  |
| RX-8 Renesis Engine Carburetor/Manifold Adaptor Plate for the 2004-2011 RX-8 Renesis (Six Port - High Power) Engine. The Carburetor/Manifold Adapter Plate is intended to adapt the Racing Beat-manufactured 1986-1992 Six Port Holley and Weber Downdraft Manifolds (Part Numbers 16476 and 16493 respectively) to the 2004 through 2010 RX-8 Renesis Engine. As delivered, the adapter plate has been ported to match the Renesis engine with the Six Port sleeves removed. The Mazda Factory RX-8 Renesis engine-to-intake multi-layer manifold gasket (13-111A-N3H3) is utilized with the adapter plate; however, the gasket is modified by drilling out the rivets that secure the multi-layer gasket. The two (2) gasket layers that are normally nearest the engine block are then used between the adapter and the engine block. The Mazda Factory 1986-92 multi-layer gasket (13-111A-N326) is utilized between the adapter plate and the carburetor manifold. | ||
| Header for RX8 | ||
|---|---|---|
| The construction is 100% 304-stainless steel and includes a genuine OEM outlet flange. | 16133 |  |
| Racing Exhaust | ||
| The Racing Beat RX-8 Race Exhaust System is a lightweight exhaust system that is intended for street or race applications.This system is significantly lighter than the stock system and has been designed to meet a race track imposed 92db sound limit. All components are handcrafted using 304-stainless steel materials for excellent durability and strength. As a weight saving measure, the decorative tip outlet was removed, and replaced with a downward-angled outlet pipe. This pipe reflects exhaust noise downward in an attempt to further dissipate the sound. | 16396 |  |
| The Racing Beat catalytic converter replacement pipe is made from full 304-stainless steel. This mandrel-bent 3” OD racing pipe is a direct bolt-on replacement for the stock catalytic converter section. This pipe utilizes a genuine OEM rear mounting flange for a secure fit to the stock (or an aftermarket) exhaust system. The race pipe is equipped with a sensor fitting for the oxygen sensor. (Note: Placement of the sensor in the pipe will cause the “check engine” light to be illuminated, but performance and engine systems will not be affected.) Each kit is supplied with all mounting hardware and detailed installation instructions | 16201 |  |
| If you require a modest, quieter exhaust tone, then the Racing Beat resonated pipe is your answer. Designed to provide the ultimate combination of performance AND sound. Racing Beat offers a full 304-stainless steel catalytic converter replacement pipe with dual resonators for RX-8 racing applications. Fitted with two (2) specially designed resonator units specifically for the RX-8 chassis. This is a direct bolt-on replacement for the stock catalytic converter section. Each replacement pipe is equipped with a sensor fitting for the oxygen sensor. (Note: Placement of the sensor in the pipe will cause the “check engine” light to be illuminated, but performance and engine systems will not be affected.) | 16221 |  |
| Now Available!
Racing Beat Gauge Panel Kit |
Monitor critical engine performance on your RX-8 with this fully functional Racing Beat Gauge Panel Kit. This kit is fully assembled and is ready for installation in your RX-8! Note: Although it is possible that this unit will mount in the auto transmission equipped RX-8, the installation instructions were written for the installation of the sensor lines through an opening near the manual shift arm. Click here for more information |  |
| Mazdatrix RX-8 Home Page | Click part number for price | View Cart |