Clutch Related Parts

Return to Main Flywheel and Clutch Page

Pilot Bearing and Bearing Removal

The Pilot Bearing and Seal must be changed whenever a new clutch is installed. We also recommend changing it whenever possible (if you have the engine or the transmission out) if there is more than 10K miles on it. We have seen many failures of the Pilot, and sometimes damage to the transmission input shaft, earlier than the actual clutch wearing out.
	Pilot Bearing (all 74-on)	11-D030-N326
	Pilot Seal (all 74-on)	11-404A-1881
The Removal Tool pays for itself the first time it is used by eliminating all frustration, bad language, and potential eccentric shaft damage by other methods. With this tool, bearing removal takes less than one minute.
	Pilot Removal Tool	49-1285-0710

Clutch Forks and Pivots
Clutch Pivot Ball	86-88 TURBO	16-1020-N302
	84-92 N/T	16-102B-0603
	89-92 TURBO	16-1020-N310
Clutch Fork	84-88 13B N/T	16-5200-N204
	86-88 TB	16-5200-N302
	89-92 N/T	16-5200-N302
	89-92 TURBO	16-5200-N310
	93-95	16-520B-N315

Clutch Alignment Tool
If the transmission is out we recommend inspecting the clutch disc and pressure plate. It is much easer to do it now than find out one or both are bad after you put the transmission back in. If you do the inspection you will need a Clutch Alignment Tool to reinstall the clutch.
	This tool (or one like it) must be used when installing any clutch (new or old) to prevent damage to disc, pilot, transmission, and/or the person attempting to put the transmission or engine back in.
All 74-92	non-turbo	49-0033-05
86-95	Turbo	49-0033-03

Clutch Misc.
Pedal Bump Stop	86-92 Brake up Clutch Down	43-0290-B001
Pedal Bump Stop	86-92 Clutch Up	43-0290-G030

Clutch Hardware
Pressure Plate Bolts (Uses 6 for 86-95 and 04-ON) (Uses 4 for 71-92 Non-Turbo, and 2 Close tolerance pilot bolts, listed below)	00-8040-9YA0
Pressure Plate Bolts (close tolerance pilot bolt) (Uses 2 for 71-92 Non-Turbo, and 4 Short, listed above)	16-4320-0839
Pressure Plate Lock Washers (Uses 6)	10-8000-9997

Rear Transmission Mount 79-85
We are finding a significant number of broken or sagging mounts that transmit noticeable vibrations into the car. It is only a few more nuts and bolts to install a new mount while the transmission is out.
84-85 Auto Trans	74-85 All Manual Trans		39-340A-1011
	74-83 Automatic Trans		39-340A-1011
	84-85 Automatic Trans		39-340B-FA55
Rear Transmission Mount 86-92
The transmission is actually held up and in place by the "Y" blocks listed below. The crossmember is more obviously bad because it's bushing actually breaks, while the "Y" blocks rarely break, they just sag, causing the bushing in the crossmember to break out. If you replace the crossmember, but not the blocks, your new crossmember will soon fail. The bushing in the center of the crossmember is not designed to carry any weight.
	86-92 Side of "Y" 2 needed		39-340A-FB01
	Competition version of above (much stiffer) 2 needed		39-3400-FBY1
	86-88 Manual Trans non-turbo		39-370D-FB01
	86-88 Turbo		39-370D-F044
	86-92 Automatic Trans		39-370C-FB02
	89-92 Manual Trans. non-turbo		39-3700-FC02
	89-92 Turbo		39-3700-FC18

Transmission Front Cover with Seal
It is always a good idea to replace the front seal on the transmission when replacing a clutch. What we are finding is considerable wear on the transmission front cover from the continual release bearing movement. If worn too much, the pressure plate will fail prematurely from release bearing side movement and misalignment.
Includes new front seal	79-80	4 and 5 speed	No Longer Available Must rebuild trans w/81+ front bearing, then use the front cover listed below.
	79-85	5-spd (use w/ 81+ front bearing)	16-220D-8540
Includes new front seal	86-92	Cast Iron non-turbo	16-220A-N204
Does NOT include front seal	86-92	Turbo	16-2210-N302
	93-95	Twin Turbo	16-2210-N315
	Front Gasket (all except Turbo)		16-2250-8540

Bellhousing to Engine Bolts (79-95)
	93-95 A/T Lower Left	61-0700-9979
	93-95 M/T (uses 4)	61-0550-9979
	Lower Left (long)	61-0900-9979
	Lower Right	41-0400-9978
	Upper Center (hook)	10-8450-8555
	Upper Left	61-0350-9979
	Upper Right	61-0450-9979

Return to Main Flywheel and Clutch Page